Therefore, this paper discussed the outlet pressure compensation in the crane hydraulic system, and analysis the unloading problems of multi-way valve system when it is in its closed position
Learn More
Applying a multi-service digital displacement® pump to an excavator to reduce valve losses. have been proposed over the years to tackle this problem, but very few of them found fertile ground
Learn More
T-T-Y head bolts are particularly common on engines using aluminum heads and/or multi-layer steel head gaskets. These bolts are engineered to stretch within a controlled "yield zone". Once they reach this zone, they spring back to provide a precise level of clamping force over the entire area of the gasket.
Learn More
Sep 08, 2021 · The most common problem in the maintenance of small excavators is that the engine cannot be controlled. Nowadays, the maintenance of excavators is becoming faster and faster, which is likely to cause major accidents, such as the destruction of …
Learn More
F. A manual valve was installed in the line to the ram that was hot. When the manual valve was closed, the pressure built up to the normal level of 2,100 psi. The problem was the prefill valve for that ram was stuck open, allowing all the pump volume to bypass back to the tank at 1,400 psi.
Learn More
Respect the flow direction indicated with an arrow on the valve body: the flow is from port 1 for 2-way valves and from port 2 for 3-way valves. Valves with an arrow printed on the body can work only in that direction. Before disconnecting or disassembling the valve, make sure that there is no pressure inside the tubing or inside the valve itself.
Learn More
https://shop.finaldriveparts.com/ 888-9-FINALS Excavator Travel Drive Motor PartsDo you have an excavator or mini excavator with problems? Have you recent
Learn More
Failing valves will emit warning signs at the first hint of trouble. For example, failing check valves will start to vibrate and even lose some internal parts when problems begin to arise. Other symptoms of check valve failure include reverse flow and excessive component wear and damage. Check valves will also emit noises as they start to break
Learn More
Jul 14, 2020 · Then, as shown in Figure 4-93, remove the multi-way control valve. Remove the hose at the side of the multi-way valve and insert a plug at each opening to avoid getting dust. (2) As shown in Figure 4-94, put a label on the hose in the remote control tube between the multi-way control valve and the pilot valve, and mark the marks from P1 to P8
Learn More
1. valve chatters, due to defective solenoid, or the voltage is too low 2. valve defective due to dirt or wear 3. through flow excessive 4. pilot pressure variations 5. on valves w/adjustable damping, the adjustment has not been carried out 6. check the electrical controls 1. cavitation problems because: a) fluid level too low b) viscosity too
Learn More
Excavator-specific Hydraulic System Solutions
Learn MoreHydraulic Valve Troubleshooting | Hydraulic Valve
Learn More
One final problem that could result in costly repairs: You notice that the equipment is using more fuel than it should, which means you are using the wrong type of fuel, the air intake system is clogged or dirty, problems with the crankcase, or you are operating the excavator improperly.
Learn More
WB93R-8 RIGID BACKHOE OADER ENGINE POWER 75 kW / 101 HP @ 2.300 rpm OPERATING WEIGHT 7.590 - 9.500 kg BUCKET CAPACITY 1,0 m³ (4×1 bucket) EU Stage IV Engine
Learn More
Common Control Valve Problems | Basic Principles of
Learn More
Rötelmann's excavator ball valves solve this problem, making it faster and safer to change attachments. The ball valves close off both sides of the bucket cylinder. The integrated check valve function enables the piston rod to retract into the cylinder, therefore preventing the rod from being pulled out.
Learn More
HYDRAULIC EXCAVATOR PC500LC-8 5 Equipped with the ECO gauge that can be recognized at a glance on the right of the multi-function color moni-tor for environment-friendly energy-saving operations. Allows focus on operation in the green range with re-duced CO 2 emissions and effi cient fuel consumption. Two return hoses im-prove hydraulic perfor
Learn More
Jul 17, 2010 · I'm working on a 303.5 excavator, all the hydraulics in the boom (all digging functions) are week, but the swing and grading blade work fine. the tracking is weak also (will travel slow, but not fast and will not pull itself around to turn) pressures at the hydrostat pump are about 1100psi in travel. pressure @ hyd pump port is 500psi. if I engage the tracking handle, my digging functions work
Learn More
Mar 30, 2021 · Insufficient leading pressure causes insufficient pressure to open the valve core, resulting in insufficient total flow and slow action; 5. To clear up whether there are problems with the power supply circuit, check the common faults of the excavator CPU, high-voltage and …
Learn More
Jun 17, 2020 · That said your's has a problem and will need to be looked at by someone with some basic trouble shooting skills. The problem could be in one of the switches in the handle mounted to the joystick or maybe in one of the solenoids on the valve body or might be a short to ground on the hot wire running from the battery to it.
Learn More